Wire drawing.html

Drawing silver wire by hand pulling.

Drawing thicker silver wire by cranked pulling.

Wire drawing is a metalworking process used to reduce the diameter of a wire by pulling the wire through a single, or series of, drawing die(s). There are many applications for wire drawing, including electrical wiring, cables, tension-loaded structural components, springs, paper clips, spokes for wheels, and stringed musical instruments. Although similar in process, drawing is different than extrusion, because in drawing the wire is pulled, rather than pushed, through the die. Drawing is usually performed at room temperature, thus classified a cold working process, but it may be performed at elevated temperatures for large wires to reduce forces.¹ Wires can also be drawn into different shapes, although this is much more difficult than diameter reductions.^{citation needed} More recently drawing has been used with molten glass to produce high quality optical fibers.^{citation needed}

1 Process
- 1.1 Lubrication
2 Drawing dies
3 See also
4 References
- 4.1 Notes
- 4.2 Bibliography

Process

The wire drawing process is quite simple in concept. The wire is prepared by shrinking the beginning of it, by hammering, filing, rolling or swaging, so that it will fit through the die; the wire is then pulled through the die. As the wire is pulled through the die, its volume remains the same, so as the diameter decreases, the length increases. Usually the wire will require more than one draw, through successively smaller dies, to reach the desired size. This can be done on a small scale with a draw plate, or on a large commercial scale using automated machinery.¹²

The areal reduction of small wires are 15–25% and larger wires are 20–45%.¹ Very fine wires are usually drawn in bundles. In a bundle, the wires are separated by a metal with similar properties, but with lower chemical resistance so that it can be removed after drawing.^{citation needed}

Commercial wire drawing usually starts with a coil of hot rolled 9 mm (0.35 in) diameter wire. The surface is first treated to remove scales. It is then fed into either a single block or continuous wire drawing machine.

Single block wire drawing machines include means for holding the dies accurately in position and for drawing the wire steadily through the holes. The usual design consists of a cast-iron bench or table having a bracket standing up to hold the die, and a vertical drum which rotates and by coiling the wire around its surface pulls it through the die, the coil of wire being stored upon another drum or "swift" which lies behind the die and reels off the wire as fast as required. The wire drum or "block" is provided with means for rapidly coupling or uncoupling it to its vertical shaft, so that the motion of the wire may be stopped or started instantly. The block is also tapered, so that the coil of wire may be easily slipped off upwards when finished. Before the wire can be attached to the block, a sufficient length of it must be pulled through the die; this is effected by a pair of gripping pincers on the end of a chain which is wound around a revolving drum, so drawing the wire until enough can be coiled two or three times on the block, where the end is secured by a small screw clamp or vice. When the wire is on the block, it is set in motion and the wire is drawn steadily through the die; it is very important that the block rotates evenly and that it runs true and pulls the wire at a constant velocity, otherwise "snatching" occurs which will weaken or even break the wire. The speed at which the wire is drawn vary greatly, according to the material and the amount of reduction.

Continuous wire drawing machines differ from the single block machines in having a series of dies through which the wire passes in a continuous manner. The difficulty of feeding between each die is solved by introducing a block between each die. The speeds of the blocks are increased successively, so that the elongation is taken up and any slip compensated for. One of these machines may contain 3 to 12 dies.² The operation of threading the wire through all the dies and around the blocks is termed "stringing-up".^{citation needed} The arrangements for lubrication include a pump which floods the dies, and in many cases also the bottom portions of the blocks run in lubricant.^{citation needed}

Often intermediate anneals are required to counter the effects of cold working, and to allow more further drawing. A final anneal may also be used on the finished product to maximize ductility and conductivity.³

An example of product produced in a continuous wire drawing machine is telephone wire. It is drawn 20 to 30 times from hot rolled rod stock.²

Lubrication

Lubrication in the drawing process is essential for maintaining good surface finish and long die life. The following are different methods of lubrication:¹

Wet drawing: the dies and wire or rod are completely immersed in lubricant
Dry drawing: the wire or rod passes through a container of lubricant which coats the surface of the wire or rod
Metal coating: the wire or rod is coated with a soft metal which acts as a solid lubricant
Ultrasonic vibration: the dies and mandrels are vibrated, which helps to reduce forces and allow larger reductions per pass

Various lubricants, such as oil, are employed. Another lubrication method is to immerse the wire in a copper (II) sulfate solution, such that a film of copper is deposited which forms a kind of lubricant. In some classes of wire the copper is left after the final drawing to serve as a preventive of rust or to allow easy soldering.^{citation needed}

Diagram of drawing wire

Drawing dies

Drawing dies are typically made of tool steel, tungsten carbide, or diamond, with tungsten carbide and manufactured diamond being the most common.² Synthetic diamond is usually used in the early stages of the drawing process, whereas natural diamond dies are used in the final stages.^{citation needed} For drawing very fine wire a single crystal diamond die is used.² For hot drawing, cast-steel dies are used.^{citation needed} For steel wire drawing, a tungsten carbide die is used.^{citation needed} The dies are placed in a steel casing, which backs the die and allow for easy die changes.² Die angles usually range from 6–15°,^{citation needed} and each die has at least 2 different angles: the entering angle and approach angle.²

References

Notes

^ ^a ^b ^c ^d Kalpakjian, pp. 415–419.
^ ^a ^b ^c ^d ^e ^f ^g Degarmo, p. 434.
^ Degarmo, p. 435.

Bibliography

Degarmo, E. Paul; Black, J T.; Kohser, Ronald A. (2003), Materials and Processes in Manufacturing (9th ed.), Wiley, ISBN 0-471-65653-4 .
Kalpakjian, Serope; Schmid, Steven R. (2006). Manufacturing Engineering and Technology, 5th edition, Upper Saddle River, NJ: Pearson Prentice Hall, 429. ISBN 0-13-148965-8.